IEC 61784-5-12:2010 pdf – lndustrial communication networks – Profiles – Part 5-12: Installation of fieldbuses- Installation profiles for CPF 12
IEC 61784-5-12:2010 pdf – lndustrial communication networks – Profiles – Part 5-12: Installation of fieldbuses- Installation profiles for CPF 12.
Where there is no corresponding subclause of lEG 61918:2010 in the normative annexes in this standard. the subclause of IEC 61918 applies without modification.
The annex heading letter represents the installation profile assigned in Clause 4. The annex
(sub)clause numbering following the annex letter shall represent the corresponding
(sub)clause numbering of IEC 61918.
EXAMPLE AnneE B.4.4 i IEC 61754-5-3 means that CP 3/2 specilies the Subclause 4.4 of IEC 61918 All main clauses of lEG 61918 are cited and apply in full unless otherwise stated in each normative installation profile annex, If all subclauses of a (sub)clause are omitted, then the corresponding IEC 61918 (sub)clause applies.
It in a (sub)clause it is written Not applicable.”, then the corresponding
IEC 61918 (sub)clause does not apply.
If in a (sub)clause it is written Addition”, then the corresponding lEG 61918 (sub)clause
applies with the additions written in the profile
If in a (sub)clause it is written Rep?acemenr, then the text provided in the protile replaces the text of the corresponding IEC 61918 (sub)clause
NOTE A replacement can also comprise additions.
If in a (sub)clause it is written ModIical,ôn:”. then the corresponding IEC 61918 (sub)clause applies with the modifications written in the profile.
If all (sub)clauses of a (sub)clause are omitted but In this (sub)clause it Is written
(Sub)cIause x has addition:” (or replacement:’) or (Sub)clause x is not applicable., then
(sub)clause x becomes valid as declared and all the other corresponding
IEC 61918 (sub)clauses apply.
6 Conformance to installation profiles
Each installation profile within this standard includes part of IEC 61918:2010. It may also include defined additional specifications.
A statement of compliance to an installation profile of this standard shall be statedZ as either
Compliance to IEC 61 784-5-12:20103 for CP 121m
Compliance to IEC 61784-5-12 (Ed.1.0) for CP 121m
where the name within the angle brackets < > is optional and the angle backets are not to be
included. The m n within CP 12/rn shall be replaced by the profile number 1 or 2.
NOTE The nema may be the name of the profile, for example EtherCATW.
If the name is a trade name then the permission of the trade name holder shall be required.
Product standards shall not Include any conformity assessment aspects (Including quality management provisions), neither normative nor informative, other than provisions for product testing (evaluation arid examination).
A.4.4.5.1 Common description
A.4.4.5.2 Specific requirements for CPa
Not applicable
A.4.4.5.3 Specific requirements for wireless installation
A.4.4.5.4 Specific requirements for generic cabling in accordance with
ISOlEC 24702
A.4.4.6 Coding and labelling
A4.4.7 Earthing and bonding of equipment and devices and shield cabling
A.4.4.8 Storage and transportation of cables
A.4.4.9 Routing of cables
A.4.4.10 Separation of circuit
Addition:
This subclause applies in principle, This means that CPI2i’l and CP12’2 networks work
properly while ensuring the distances of Table 16 provided in IEC 61918:2010,
A.4.4.11 Mechanical protection of cabling components
A.4.4.11.1 Common description
A.4.4 11.2 Specific requirements for CP5
Not applicable.
A.4.4.11.3 Specific requirements (or generic cabling in accordance with ISOIEC 24702
A.4.4.12 installation in special areas
A.4.4.12.1 Common description
A.4.4.12.2 Specific requirements for CP5
Not applicable.
A.4.4.12.3 Specific requirements for generic cabling in accordance with
ISO.’IEC 24702
A.4.5 Cabling planning documentation
A.4.6 Verification of cabling planning specification
A.5 installation implementation
A.5.1 General requirements
A.5.2 Cable installation
A.5.2.1 General requirements for all cabling types
A.5.2.2 Installation and routing