ASME QEI-1-2018 pdf – Standard for the Qualification of Elevator Inspectors
ASME QEI-1-2018 pdf – Standard for the Qualification of Elevator Inspectors. (J) working knowledge of inspection and testing procedures as described in ASME A17.2 and awareness of published interpretations of those procedures (k) working knowledge of applicable building, fire, electrical,...
ASME QAI-1-2005 pdf – Qualifications for Authorized Inspection
ASME QAI-1-2005 pdf – Qualifications for Authorized Inspection. 1-3.1.2 Demonstrated ability to perform shop and feld inspections to the satisfaction of the Authorized Inspection Agency employing the Inspector. 1-3.1.3 Experience, knowledge, and background consistent with the complexity of the assignment....
ASME QAI-1-2003 pdf – QUALFCATIONS FOR AUTHORIZED INSPECTION
ASME QAI-1-2003 pdf – QUALFCATIONS FOR AUTHORIZED INSPECTION. The Authorized Nuclear inspector Supervisor shall perform the following duties. 1-2.2.1 Maintain a record of Certificate Holders’ shop and field sites where Inspectors assigned to him hy his AlIthnri7ed Inspection Agency for...
ASME PTC-18-2002 pdf – HYDRAULIC TURBINES AND PUMP-TURBINES
ASME PTC-18-2002 pdf – HYDRAULIC TURBINES AND PUMP-TURBINES. Unless otnerwise provided, head losses between tile high-pressure and low-pressure sections are charged to the machine. Other head losses including those due to conduits upstream and/or downstream of the machine intakes, trashracks,...
ASME PTC 53-2018 pdf – Mechanical and Thermal Energy Storage Systems
ASME PTC 53-2018 pdf – Mechanical and Thermal Energy Storage Systems. Each Code will specify using either the higher or lower heating value, typically expressed as British thermal units per pound mass (kilojoules per kilogram). Water vapor is one of...
ASME PTC 50-2002 pdf – FUEL CELL POWER SYSTEMS PERFORMANCE
ASME PTC 50-2002 pdf – FUEL CELL POWER SYSTEMS PERFORMANCE. (k) requisite facilities for maintaining constancy of load during test; (I) number of identical tests to be conducted to assure statistically significant accuracy; (m) duration of the test runs; (n)...
ASME PTB-13-2021 pdf – Criteria for Pressure Retaining Metallic Components Using Additive Manufacturing
ASME PTB-13-2021 pdf – Criteria for Pressure Retaining Metallic Components Using Additive Manufacturing. ADDITIVE MANUFACTURING DESIGN REQUIREMENTS a) In addition to the design requirements of the ASME Construction Code or Standard, the design requirements in 6(b) through 6(g) apply for...
ASME PALD-2003 pdf – SAFETY STANDARD FOR PORTABLE AUTOMOTIVE LIFTING DEVICES
ASME PALD-2003 pdf – SAFETY STANDARD FOR PORTABLE AUTOMOTIVE LIFTING DEVICES. This Part applies to transmission jacks that are used to remove and install transmissions and differential assemblies from automobiles and trucks. 2-1.2 Classification Hydraulic, pneumatic, and mechanical are the...
ASME NTB-4-2021 pdf – Background Information for Addressing Adequacy or Optimization of ASME BPVC Section II, Division 5 Rules for Nonmetallic Core Components
ASME NTB-4-2021 pdf – Background Information for Addressing Adequacy or Optimization of ASME BPVC Section II, Division 5 Rules for Nonmetallic Core Components. The output from the tensile geometry FE model (VP-O0) was calibrated with the tensile experimental test results,...
ASME N511-2007 pdf – In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems
ASME N511-2007 pdf – In-Service Testing of Nuclear Air Treatment, Heating, Ventilating, and Air-Conditioning Systems. 5.4.1 In-Service Test Requirements. In-service tests listed in Table 5 shall be conducted at the specified interval and test results verified to be within the...