ASME CA-1-2014 pdf – Conformity Assessment Requirements
ASME CA-1-2014 pdf – Conformity Assessment Requirements. 5.1.3 The Certification Mark and certification designator shall be discernible. (a) When the size or use of the item will not permit the direct application of the Certification Mark and certification designator, or...
ASME BPVC-VII ADD-2008 pdf – RECOMMENDED GUIDELINES FORTHE CARE OF POWER BOILERS
ASME BPVC-VII ADD-2008 pdf – RECOMMENDED GUIDELINES FORTHE CARE OF POWER BOILERS. This international code or standard was developed under procedures accredited as meeting the criteria for American National Standards and it is an American National Standard. The Standards Committee...
ASME BPE-2002 pdf – BIOPROCSSING EQUIPMENT
ASME BPE-2002 pdf – BIOPROCSSING EQUIPMENT. SD-3.4.7 Internally cnated glass shall only be lsed if the coating complies with FDA or other regulatory authority and approved by uhe owner/user. SD-3.5 Fabrication SD-3.5.1 Fabrication shall be performed in facilites where the...
ASME B107.410-2008 pdf – Struck Tools
ASME B107.410-2008 pdf – Struck Tools . 5.2 Materials The materials used in the manufacture of extractors shall be such as to produce tools conforming to this Standard. 5.3 Mechanical Properties Hardness of the cutting edges shall be 45 HRC...
ASME B107.60-2004 pdf – Pry Bars
ASME B107.60-2004 pdf – Pry Bars. hund1e addihonal material that is securely attached to the body and s to be gripped during use. point end portion of bar having a tapered. mund. crosssectionai area that is intended for aligning applications....
ASME HST-1-2017 pdf – Performance Standard for Electric Chain Hoists
ASME HST-1-2017 pdf – Performance Standard for Electric Chain Hoists. 1-1.3.3 RandomLy Distributed Loads Randomly distributed implies that loads applied to the hoist are assumed to be evenly distributed within the rated load of the hoist in decreasing steps of...
ASME B107.300-2021 pdf – Hand Torque Tools and Torque Testers
ASME B107.300-2021 pdf – Hand Torque Tools and Torque Testers. 6.2 ParaLLax Error — Category 14, Type I The torque instrument scale shall be located so that it is in a horizontal plane. The pointer shall be adjusted to indicate...
ASME B107.53-2004 pdf – Ball Peen Hammers: Safety Requirements
ASME B107.53-2004 pdf – Ball Peen Hammers: Safety Requirements. 5.5 Grip Test 5.5.1 Hammers shaibe secured by hand and thegrip nwisted at the normal hand grip position in altemating directions Five altemating, twisting motions shall be performed. ater which there...
ASME B107.36-2002 pdf – PLIERS; LOCKING, CLAMP, AND TUBING PINCH-OFF
ASME B107.36-2002 pdf – PLIERS; LOCKING, CLAMP, AND TUBING PINCH-OFF . 4.4 Handles Handlcs of pliers shall be through hardened from 3OtoSOllRCorcasebaidcnedfrom75toH6HRl5N, with a ca.sc depth of a minimum of 0.010 in. (0.23 mm). HandLes shall be so shaped as...
ASME B107.18-2003 pdf – PLIERS: WIRE TWISTER
ASME B107.18-2003 pdf – PLIERS: WIRE TWISTER. Wire twister pliers shall incorporate a device, which, when actuated, will cause the pliers to rotate about its longitudinal axis. The halves of the pliers shall be permanently joined with a through fastener...